Is your barrel cactus sprouting babies? Barrel cactus pups often develop on the mature plant. Many leave them and let them grow, creating a globular design in the container or in the ground. You can propagate these for new plants too.
Propagating a Barrel Cactus
You can remove the pups from the mother to plant in a container or a different spot in the garden
bed. Of course, you’ll want to do this carefully, avoiding the prickly and
painful cactus spines.
Heavy gloves are a necessary part of the protection you’ll
need to use when propagating a barrel cactus. Some wear two pairs of gloves
when working with cactus, as the spines easily pierce through.
Tools with handles, such as tongs, and a sharp knife or
pruners allow you to reach the bottom of the pup without injuring yourself.
Evaluate which tool will work best for your situation.
How to Propagate Barrel Cacti
Cover the mother barrel cactus plant, leaving the baby
exposed. Some use plastic nursery pots for this part of the chore. Others cover
with tightly wrapped newspaper for protection. Remove the pups at ground level.
Then securely pull and elevate the baby, so the stem is visible and slice it
off. Try to do this with one cut.
One cut for each removal causes less stress on both the
mother and the pup. Clip the stem as close to the main plant as possible. Clean
the knife or pruners before starting and following each cut.
Often, the pups can twist off if you use tongs, so you might try it that way if you can get a good grip. If you wish to attempt this method, use tongs to hold the baby and twist.
Remove all pups you wish to take. Put them aside to callous over before repotting. Move the mother plant into a partially shaded area for recovery. Repot the pups into a container or bed of cactus mix topped with 2 inches (5 cm.) of coarse sand. Limit watering for a week or two.
If the destination bed is in full sun and the pup was
accustomed to some shade from the mother plant, let it root in a container.
Later, move it into the bed after roots have developed.
Is your barrel cactus sprouting babies? Barrel cactus pups often develop on the mature plant. Many leave them and let them grow, creating a globular design in the container or in the ground. You can propagate these for new plants too.
Propagating a Barrel Cactus
You can remove the pups from the mother to plant in a container or a different spot in the garden
bed. Of course, you’ll want to do this carefully, avoiding the prickly and
painful cactus spines.
Heavy gloves are a necessary part of the protection you’ll
need to use when propagating a barrel cactus. Some wear two pairs of gloves
when working with cactus, as the spines easily pierce through.
Tools with handles, such as tongs, and a sharp knife or
pruners allow you to reach the bottom of the pup without injuring yourself.
Evaluate which tool will work best for your situation.
How to Propagate Barrel Cacti
Cover the mother barrel cactus plant, leaving the baby
exposed. Some use plastic nursery pots for this part of the chore. Others cover
with tightly wrapped newspaper for protection. Remove the pups at ground level.
Then securely pull and elevate the baby, so the stem is visible and slice it
off. Try to do this with one cut.
One cut for each removal causes less stress on both the
mother and the pup. Clip the stem as close to the main plant as possible. Clean
the knife or pruners before starting and following each cut.
Often, the pups can twist off if you use tongs, so you might try it that way if you can get a good grip. If you wish to attempt this method, use tongs to hold the baby and twist.
Remove all pups you wish to take. Put them aside to callous over before repotting. Move the mother plant into a partially shaded area for recovery. Repot the pups into a container or bed of cactus mix topped with 2 inches (5 cm.) of coarse sand. Limit watering for a week or two.
If the destination bed is in full sun and the pup was
accustomed to some shade from the mother plant, let it root in a container.
Later, move it into the bed after roots have developed.